Commuter Craft Innovator Aircraft’s Official Unveiling Excites Crowds at OshKosh 2016!

plane-in-front-of-curtain-quartered_v2_2500 (1)(1)


Atlanta, Georgia: Commuter Craft officially launched its Innovator Aircraft at the 2016 OshKosh Airventure Show to an overwhelmingly enthusiastic response! Richard Hogan, Commuter Craft’s founder and president, was pleased at the excitement and buzz over the much anticipated introduction of the Innovator! With its unique, sleek lines and powerful components, the Innovator commanded the attention of all that came by the Commuter Craft Exhibit!

Commuter Craft is starting production with six “AlphaShips” this fall with these first production aircraft being customer built in the Commuter Craft’s 82,000 square foot Facility under the Experimental aircraft category. This will be followed by construction of eight “BetaShip” aircraft, leading to full general production in 2017. Commuter Craft began taking position reservations in April of this year, and will continue to offer its pre-production special until September 6, 2016.

The Innovator is a next generation two-place aircraft designed to provide best-in-class performance and safety features not found in other general aviation aircraft. Featuring a three-surface blend wing, lifting body airframe, the Innovator top speed is over 200 miles per hour, with a 180 hp. engine and fixed landing gear. The unique configuration is inherently stall and spin resistant while providing excellent low speed handling. The 60” wide cabin and variable geometry seats provide comfort for pilots from 5’0 to 6’9 tall, with ample room for baggage. Fully loaded, the Innovator has a range of 800 nautical miles.

To make aviation more affordable and accessible, Commuter Craft designed the Innovator airframe to EAB category requirements. The aircraft kits will be customer built in 2 to 3 weeks in its facility, utilizing factory tooling. The Factory Builder Program saves time and money, eliminating the cost of expensive tools or dedicated build space. The build process is primarily assembly and bonding with very little fabrication. A dedicated technician is provided for each builder to insure quality and proper technique. Upon completion of the airframe, factory options are available for engine, propeller, instruments, interior and paint packages to finish the Innovator aircraft in as little as three months total, compared to the average kit built time of seven years.

Commuter Craft was formed in 2006 and has established its world headquarters and factory in Cartersville, Georgia. The Innovator is first in a planned line of personal transportation vehicles designed to provide leading edge technology, performance, efficiency and utility for the next generation and beyond.

Commuter Craft’s address is 63 Industrial Drive, Cartersville, Georgia 30120.
Email is (770) 722-2514. offers technical information about the Innovator and the Factory Builder Program.


  1. immunforsvaret - June 2, 2018

    … [Trackback]

    […] Find More on|Find More|Find More Infos here|Here you will find 45754 additional Infos|Informations to that Topic: […]

  2. different types of psychic readings - June 2, 2018

    … [Trackback]

    […] Find More here|Find More|Find More Infos here|There you will find 48970 additional Infos|Infos to that Topic: […]

  3. diyala coehuman - June 4, 2018

    … [Trackback]

    […] Find More here|Find More|Read More Infos here|There you can find 42969 additional Infos|Infos to that Topic: […]

  4. forex signals - June 5, 2018

    … [Trackback]

    […] Read More on|Read More|Read More Informations here|Here you can find 38439 additional Informations|Informations to that Topic:…

  5. in vivo pharmacokinetic properties - June 19, 2018

    … [Trackback]

    […] Read More here|Read More|Find More Informations here|Here you can find 35965 more Informations|Infos to that Topic: […]